Photo: Timothyjosephwood · CC BY-SA 4.0 · Source
Hang, tape and finish 1/2 in. gypsum board (Level 4) on walls and ceilings, per sq ft of board.
Install Gypsum Board typically costs $1.60 to $3.50 per sq ft (national average as of 2026). Most straightforward jobs start near $1.60 per sq ft. Final pricing depends on material quality, project scope, local labor rates, and site conditions. Use our free calculator below for a personalized estimate.
Quality Level
Estimated Total Cost
200 sq ft • Standard Quality
National average — enter your ZIP for local prices.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
$1.36 – $2.97 per sq ft
1/2 in. standard gypsum board on walls and ceilings, paper tape and all-purpose compound, Level 4 finish ready for primer
$1.60 – $3.50 per sq ft
1/2 in. lightweight board on walls, 1/2 in. sag-resistant board on ceilings, paper tape, metal corner bead, Level 4 finish
$2 – $4.38 per sq ft
1/2 in. lightweight board with sag-resistant ceilings and moisture-resistant board in wet areas, paper-faced metal bead, Level 4 finish
| Component | Category | Low | High | Unit |
|---|---|---|---|---|
| Materials | material | $0.72 | $1.57 | sq ft |
| Labor | labor | $0.56 | $1.22 | sq ft |
| Supplies & Other | supplies | $0.19 | $0.42 | sq ft |
| Equipment & Disposal | equipment | $0.13 | $0.29 | sq ft |
Hang, tape and finish 1/2 in. gypsum board (Level 4) on walls and ceilings, per sq ft of board.
Typical install gypsum board pricing range per sq ft.
Starting price $1.60 per sq ft. National average as of 2026. This is a directional range. Final pricing depends on scope, materials, access, and local labor rates.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
Close-up of a gypsum board face with screw heads and a tapered seam
Photo: Panamitsu · CC BY-SA 4.0 · Source
Find a pro to do thisInstall Gypsum Board usually lands between $1.60 to $3.50 per sq ft. That range reflects current national calculator data after materials, labor, supplies, equipment, and disposal are rolled together. Your real quote will move based on quantity, site conditions, finish level, and contractor availability in your ZIP code.
Hang, tape and finish 1/2 in. gypsum board (Level 4) on walls and ceilings, per sq ft of board.
Material selections can move the budget faster than anything else, with current material allowances landing around $0.72 to $1.57 per sq ft.
Labor complexity is the next major swing factor, with installation or trade time currently averaging $0.56 to $1.22 per sq ft.
Smaller consumables still matter, because supplies are contributing about $0.19 to $0.42 per sq ft.
Specialty tools, access equipment, cleanup, and disposal can add another $0.13 to $0.29 per sq ft.
Scope changes, premium finishes, difficult access, demolition, and permit requirements can push the total toward the high end of the range. Cleaner access, standard finishes, and bundled work often keep the job closer to the low end.
Get multiple itemized bids, ask contractors to separate materials from labor, and confirm what is included before you compare totals. Scheduling during a slower season and bundling adjacent work can also reduce mobilization costs.
Keep specifications tight before work starts. Change orders are one of the fastest ways to blow past the original budget, especially when material lead times or specialty trades are involved.
DIY can make sense when you already own the tools, understand the prep requirements, and can tolerate schedule risk. Hiring a pro is usually the better move when mistakes would affect finish quality, code compliance, waterproofing, structural performance, or warranty coverage.
View local pricing for install gypsum board across 51 states.
Find contractors who list this service and ask for a written quote.
Cost guides for property owners. Contractor ID for the shops who do the work.
Close-up of a knockdown-textured drywall ceiling
Photo: Loadmaster (David R. Tribble) This image was made by Loadmaster (David R. Tribble) . Email the author: David R. Tribble Also see my personal gallery at Google Photos · CC BY-SA 3.0 · Source
Find a pro to do thisUse the calculator range of $1.60 to $3.50 per sq ft as your baseline, then compare that against the time, tool rentals, material waste, and rework risk you would take on by doing the project yourself.
Most install gypsum board jobs start with site review, measurements, and material confirmation. From there the crew usually handles preparation, core installation or repair work, cleanup, and a final walkthrough to confirm the finished scope matches the quote.
Ask each contractor how they handle protection of adjacent finishes, debris removal, and change approvals. Those three points tend to separate a clean project from an expensive headache.