Basic
$595 – $1,700 each
Single-layer steel raised-panel sectional door, non-insulated, white, torsion springs, new tracks and hardware

Remove old door and supply and install a sectional raised-panel steel garage door (single or standard double) with tracks, springs and hardware.
Panel Garage Door typically costs $700 to $2,000 each (national average as of 2026). Most straightforward jobs start near $700 each. Final pricing depends on material quality, project scope, local labor rates, and site conditions. Use our free calculator below for a personalized estimate.
Quality Level
Estimated Total Cost
1 unit(s) • Standard Quality
National average — enter your ZIP for local prices.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
Tell us about your project and we'll send it to contractors near you who do this work.
$595 – $1,700 each
Single-layer steel raised-panel sectional door, non-insulated, white, torsion springs, new tracks and hardware
$700 – $2,000 each
Two-layer steel raised-panel door with polystyrene insulation, almond, torsion springs, new tracks and hardware
$875 – $2,500 each
Three-layer steel raised-panel door with polyurethane insulation, white, window lites in top section, high-cycle springs
| Component | Category | Low | High | Unit |
|---|---|---|---|---|
| Materials | material | $315 | $900 | each |
| Labor | labor | $245 | $700 | each |
| Supplies & Other | supplies | $84 | $240 | each |
| Equipment & Disposal | equipment | $56 | $160 | each |
Remove old door and supply and install a sectional raised-panel steel garage door (single or standard double) with tracks, springs and hardware.
Typical panel garage door pricing range each.
Starting price $700 each. National average as of 2026. This is a directional range. Final pricing depends on scope, materials, access, and local labor rates.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
White paneled garage door with window lites on a house with paver driveway
Photo: Stilfehler · CC BY-SA 4.0 · Source
Find a pro to do thisPanel Garage Door usually lands between $700 to $2,000 each. That range reflects current national calculator data after materials, labor, supplies, equipment, and disposal are rolled together. Your real quote will move based on quantity, site conditions, finish level, and contractor availability in your ZIP code.
Remove old door and supply and install a sectional raised-panel steel garage door (single or standard double) with tracks, springs and hardware.
Material selections can move the budget faster than anything else, with current material allowances landing around $315 to $900 each.
Labor complexity is the next major swing factor, with installation or trade time currently averaging $245 to $700 each.
Smaller consumables still matter, because supplies are contributing about $84 to $240 each.
Specialty tools, access equipment, cleanup, and disposal can add another $56 to $160 each.
Scope changes, premium finishes, difficult access, demolition, and permit requirements can push the total toward the high end of the range. Cleaner access, standard finishes, and bundled work often keep the job closer to the low end.
Get multiple itemized bids, ask contractors to separate materials from labor, and confirm what is included before you compare totals. Scheduling during a slower season and bundling adjacent work can also reduce mobilization costs.
Keep specifications tight before work starts. Change orders are one of the fastest ways to blow past the original budget, especially when material lead times or specialty trades are involved.
DIY can make sense when you already own the tools, understand the prep requirements, and can tolerate schedule risk. Hiring a pro is usually the better move when mistakes would affect finish quality, code compliance, waterproofing, structural performance, or warranty coverage.
BuildX Pro researches and reviews the national price range for Panel Garage Door, then adjusts it to your ZIP code for local labor and material costs using the public data below. Last checked Nov 2026.
View local pricing for panel garage door across 51 states.
Find contractors who list this service and ask for a written quote.
Cost guides for property owners. Contractor ID for the shops who do the work.
Horizontal-section garage door on a stucco house with potted plant
Photo: Stilfehler · CC BY-SA 4.0 · Source
Find a pro to do thisUse the calculator range of $700 to $2,000 each as your baseline, then compare that against the time, tool rentals, material waste, and rework risk you would take on by doing the project yourself.
Most panel garage door jobs start with site review, measurements, and material confirmation. From there the crew usually handles preparation, core installation or repair work, cleanup, and a final walkthrough to confirm the finished scope matches the quote.
Ask each contractor how they handle protection of adjacent finishes, debris removal, and change approvals. Those three points tend to separate a clean project from an expensive headache.