Photo: Asurnipal · CC BY-SA 4.0 · Source
Replace an in-ground pool filter (sand, cartridge or DE), unit and installation.
Replace Pool Filter typically costs $500 to $2,000 per project (national average as of 2026). Most straightforward jobs start near $500 per project. Final pricing depends on material quality, project scope, local labor rates, and site conditions. Use our free calculator below for a personalized estimate.
Quality Level
Estimated Total Cost
Standard Quality
National average — enter your ZIP for local prices.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
$425 – $1,700 per project
Filter of the existing type sized to the pump, standard tank, new unions and pressure gauge
$500 – $2,000 per project
Same-type filter sized to the pump with heavier-wall tank, new valve where the type uses one, unions, gauge and air relief
$625 – $2,500 per project
Same-type filter sized to the pump in a corrosion-resistant tank, new valve where used, unions, gauge and air relief
| Component | Category | Low | High | Unit |
|---|---|---|---|---|
| Materials | material | $225 | $900 | job |
| Labor | labor | $175 | $700 | job |
| Supplies & Other | supplies | $60 | $240 | job |
| Equipment & Disposal | equipment | $40 | $160 | job |
Replace an in-ground pool filter (sand, cartridge or DE), unit and installation.
Typical replace pool filter pricing range per project.
Starting price $500 per project. National average as of 2026. This is a directional range. Final pricing depends on scope, materials, access, and local labor rates.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
Replace Pool Filter usually lands between $500 to $2,000 per project. That range reflects current national calculator data after materials, labor, supplies, equipment, and disposal are rolled together. Your real quote will move based on quantity, site conditions, finish level, and contractor availability in your ZIP code.
Replace an in-ground pool filter (sand, cartridge or DE), unit and installation.
Material selections can move the budget faster than anything else, with current material allowances landing around $225 to $900 per project.
Labor complexity is the next major swing factor, with installation or trade time currently averaging $175 to $700 per project.
Smaller consumables still matter, because supplies are contributing about $60 to $240 per project.
Specialty tools, access equipment, cleanup, and disposal can add another $40 to $160 per project.
Scope changes, premium finishes, difficult access, demolition, and permit requirements can push the total toward the high end of the range. Cleaner access, standard finishes, and bundled work often keep the job closer to the low end.
Get multiple itemized bids, ask contractors to separate materials from labor, and confirm what is included before you compare totals. Scheduling during a slower season and bundling adjacent work can also reduce mobilization costs.
Keep specifications tight before work starts. Change orders are one of the fastest ways to blow past the original budget, especially when material lead times or specialty trades are involved.
DIY can make sense when you already own the tools, understand the prep requirements, and can tolerate schedule risk. Hiring a pro is usually the better move when mistakes would affect finish quality, code compliance, waterproofing, structural performance, or warranty coverage.
View local pricing for replace pool filter across 51 states.
Find contractors who list this service and ask for a written quote.
Cost guides for property owners. Contractor ID for the shops who do the work.
Use the calculator range of $500 to $2,000 per project as your baseline, then compare that against the time, tool rentals, material waste, and rework risk you would take on by doing the project yourself.
Most replace pool filter jobs start with site review, measurements, and material confirmation. From there the crew usually handles preparation, core installation or repair work, cleanup, and a final walkthrough to confirm the finished scope matches the quote.
Ask each contractor how they handle protection of adjacent finishes, debris removal, and change approvals. Those three points tend to separate a clean project from an expensive headache.