Photo: Crownbuild · CC BY-SA 3.0 · Source
Install a fully adhered or mechanically attached EPDM rubber membrane on a low-slope roof, including tear-off of one layer and flashing.
EPDM Roof typically costs $5 to $10 per sq ft (national average as of 2026). Most straightforward jobs start near $5 per sq ft. Final pricing depends on material quality, project scope, local labor rates, and site conditions. Use our free calculator below for a personalized estimate.
Quality Level
Estimated Total Cost
200 sq ft • Standard Quality
National average — enter your ZIP for local prices.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
Tell us about your project and we'll send it to contractors near you who do this work.
$4.25 – $8.50 per sq ft
45-mil black EPDM membrane fully adhered after one-layer tear-off, taped seams, standard flashings and drip edge
$5 – $10 per sq ft
60-mil black EPDM fully adhered over a new cover board, seam tape, pressure-sensitive flashings and metal edge trim
$6.25 – $13 per sq ft
60-mil reinforced EPDM fully adhered over a cover board, wider seam tape, preformed corners and pipe boots, heavier edge metal
| Component | Category | Low | High | Unit |
|---|---|---|---|---|
| Materials | material | $2.25 | $4.50 | sq ft |
| Labor | labor | $1.75 | $3.50 | sq ft |
| Supplies & Other | supplies | $0.60 | $1.20 | sq ft |
| Equipment & Disposal | equipment | $0.40 | $0.80 | sq ft |
Install a fully adhered or mechanically attached EPDM rubber membrane on a low-slope roof, including tear-off of one layer and flashing.
Typical epdm roof pricing range per sq ft.
Starting price $5 per sq ft. National average as of 2026. This is a directional range. Final pricing depends on scope, materials, access, and local labor rates.
Estimates are approximate and vary by location, project scope, and current market conditions. Contact a local contractor for an accurate quote.
Large flat roof finished with an EPDM rubber membrane and upstand edge
Photo: Crownbuild · CC BY-SA 3.0 · Source
Find a pro to do thisEPDM Roof usually lands between $5 to $10 per sq ft. That range reflects current national calculator data after materials, labor, supplies, equipment, and disposal are rolled together. Your real quote will move based on quantity, site conditions, finish level, and contractor availability in your ZIP code.
Install a fully adhered or mechanically attached EPDM rubber membrane on a low-slope roof, including tear-off of one layer and flashing.
Material selections can move the budget faster than anything else, with current material allowances landing around $2.25 to $4.50 per sq ft.
Labor complexity is the next major swing factor, with installation or trade time currently averaging $1.75 to $3.50 per sq ft.
Smaller consumables still matter, because supplies are contributing about $0.60 to $1.20 per sq ft.
Specialty tools, access equipment, cleanup, and disposal can add another $0.40 to $0.80 per sq ft.
Scope changes, premium finishes, difficult access, demolition, and permit requirements can push the total toward the high end of the range. Cleaner access, standard finishes, and bundled work often keep the job closer to the low end.
Get multiple itemized bids, ask contractors to separate materials from labor, and confirm what is included before you compare totals. Scheduling during a slower season and bundling adjacent work can also reduce mobilization costs.
Keep specifications tight before work starts. Change orders are one of the fastest ways to blow past the original budget, especially when material lead times or specialty trades are involved.
DIY can make sense when you already own the tools, understand the prep requirements, and can tolerate schedule risk. Hiring a pro is usually the better move when mistakes would affect finish quality, code compliance, waterproofing, structural performance, or warranty coverage.
View local pricing for epdm roof across 51 states.
Find contractors who list this service and ask for a written quote.
Cost guides for property owners. Contractor ID for the shops who do the work.
Flat roof covered with EPDM membrane, edge trim and a ladder
Photo: KVDP · Public domain · Source
Find a pro to do thisUse the calculator range of $5 to $10 per sq ft as your baseline, then compare that against the time, tool rentals, material waste, and rework risk you would take on by doing the project yourself.
Most epdm roof jobs start with site review, measurements, and material confirmation. From there the crew usually handles preparation, core installation or repair work, cleanup, and a final walkthrough to confirm the finished scope matches the quote.
Ask each contractor how they handle protection of adjacent finishes, debris removal, and change approvals. Those three points tend to separate a clean project from an expensive headache.